Logo

B1970 Engine Trouble Code

B1970 Engine

When you check engine light came on code B1970 the reason should be . However your vehicle's manufacturer may have a different definition for the B1970 OBD-II Diagnostic Body (B) Trouble Code. So you should chech it on our car models.

When the DTC check engine light comes B1970 code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.

B1970 Code Meaning :

B
OBD-II Diagnostic Body (B) Trouble Code For Engine
1
Fuel And Air Metering
9
Fuel Rail/System Pressure - Too High
7
Injection lump Fuel Metering Control 'B' High (Cam/Rotor/Injector)
0
Exhaust Gas Recirculation Sensor B Circuit High

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

B1970 OBD-II Diagnostic Body (B) Trouble Code Description

B1970 engine trouble code is about Exhaust Gas Recirculation Sensor B Circuit High. Fuel Rail/System Pressure - Too High and Injection lump Fuel Metering Control 'B' High (Cam/Rotor/Injector) causes most of code B1970.

Reason For B1970 Code

The reason of B1970 OBD-II Engine Trouble Code is Fuel Rail/System Pressure - Too High.

B1970 DTC reports a sensor fault, replacement of the sensor is unlikely to resolve the underlying problem. The engine error is most likely to be caused by the systems that the sensor is monitoring, but might even be caused by the wiring to the sensor itself.

How To Repair B1970 Code

Before starting let's see B1970 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access B1970 code stored in the ECU.
  • Technicians will note B1970 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

The reductant injector is part of the system that reduces the gas that is expelled through either the catalytic converter in gas engines, or the particulate filter in diesel engines. There are sensors in the exhaust system, used by the reductant injector to input voltage readings to the PCM.

B1970 code is stored again, the mechanic will perform a visual inspection of the pressure control solenoid and related systems. If any circuits or connections are damaged or loose, they will resolve these issues and move on to retest the system.

Sometimes B1970 code comes with B197000 code.

Diagnosis Of Engine Error OBD Code B1970

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a B1970 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the B1970 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.